TailFit user manual
How TailFit works, what every control does, how to read the display and what to keep in mind on different material.
- Product
- TailFit
- Applies to
- Version 1.1.0
TailFit shortens the decay of sounds. Set how long each sound may ring, and TailFit fits every tail to that length while leaving the attack of each hit untouched. It works the same way on a single kick, a full drum break or a bass line.
Quick start
- Insert TailFit on an audio track: drums, a break, bass or a synth part.
- Play the track. The display shows each detected hit (blue triangle) and where its tail now ends (short accent-coloured mark).
- Turn Tail Length until the sound is as tight as you want.
- Adjust Fit Amount for a lighter or stronger effect.
Main controls
Tail Length
Range 10 ms to 2 s. How long each sound may ring after its hit. It is measured from the start of the hit to the point where the output has fallen 40 dB below that hit’s peak, which is where a tail stops being heard in a mix. The same setting gives the same length on quiet and loud material.
TailFit never makes a sound longer: if a sound already ends sooner, it is left alone. The buttons below the slider set common lengths (50, 100, 150, 250 and 500 ms).
Fit Amount
Range 0 to 100 %. How strongly tails are fitted to the target. At 0 % the audio is untouched, at 50 % half the reduction is applied everywhere, and at 100 % the target is reached exactly.
Attack Protect
Range 0 to 100 ms. The start of every hit that is never touched, including hits that arrive while an earlier sound is still ringing. Raise it to keep more punch and body.
Shape
How the tail is brought down:
- Smooth starts easing the level right after the attack. Soft and natural on plucks, keys and percussion.
- Natural holds the body, then fades like extra damping. The default for most sounds.
- Tight keeps the full body, then cuts fast and firmly. Suited to punchy kicks, stabs and breaks.
Sensitivity
Default 60 %. How easily a new hit is recognised. Raise it if quiet hits in a busy loop are being reduced together with the tail before them (busy open hi-hats need about 90 %). Lower it if TailFit reacts to noise or wobble in sustained sounds.
Input filters, mix and output
HP and LP input filters
HP removes the lows below its frequency (20 Hz to 1 kHz) and LP removes the highs above its frequency (1 to 20 kHz), at 12 dB per octave.
- Click a filter’s button to switch it on or off.
- Drag its slider to set the frequency, double-click the slider to reset it, or double-click the value to type one (for example 120 or 1.2k).
The filters work before TailFit detects hits, so a high-pass filter also stops rumble from being taken for a new hit. Switching and frequency changes are smooth, so both can be automated. Both filters are off by default; with both off, TailFit sounds exactly as it would without them. Bypass returns the original, unfiltered sound.
Mix and Output
Mix blends the original and the processed sound. The filters stay active at every Mix setting. Output sets the level after processing.
Hear removed
Plays only what TailFit takes away: a quick way to check that no attacks are touched. Content removed by the input filters is not included.
Header: presets, A/B, bypass and colour
- Presets: the arrows step through presets. Click the preset name for the list and Save current settings as….
- A/B: compare two settings.
- Bypass: returns the original sound. Bypass keeps the same latency, so timing never jumps.
- Accent colour: the round button at the top right sets the colour of the display and controls: yellow (default), pink, green, cyan or purple. The colour is saved with your project; presets and A/B do not change it.
Hover over any control for a short explanation. The interface can be scaled to suit your screen.
The display
The last 3 seconds of audio scroll from right to left at a constant speed.
- Grey is the output, outlined in the accent colour.
- The dashed line is the input (after the HP and LP filters, when they are on).
- The tinted accent-coloured area is what was removed.
- The blue band after each hit is the protected attack; the short accent marks show where each tail should end.
When the audio stops, the whole waveform scrolls out, the display stays empty for a moment and then shows Waiting for audio.
Rarely, the display cannot show every part of the audio, for example if the host stalls the window. Such places are marked rather than hidden: a dimmed column with a small grey mark below the display means the analysis of that moment is incomplete (normal at the very end of playback), and a bright mark below the display means display data was lost. The audio itself is never affected.
Good to know
- TailFit adds 3 ms of latency, which hosts compensate automatically.
- On mixed loops one gain controls everything: when a new hit arrives while an earlier tail is still loud, that tail passes with the new hit. TailFit does not separate sounds.
- Steady beds (room tone, noise, pads under drums) are learned from the gaps and are not chopped, including through long drum pauses. A level counts as a bed when it sits at least 12 dB below the hits around it. The very first hit after playback starts may cut through a bed until the next hit.
- Bass and synth lines work note by note, so notes need their own attack. One long held note is one sound: it is fitted to the Tail Length after its attack, the same way on every pass of a loop.
- Steady noise on its own (room tone or hiss with no hits) is left alone until the detector reacts to one of the noise’s own peaks. From there the noise is faded out over the Tail Length, smoothly, like any sustained sound. Noise under real hits is kept. A lower Sensitivity makes this less likely but does not rule it out; to keep noise on its own untouched, bypass TailFit for that part.
Known limitations
- Overlapping sounds share one gain. When a new hit arrives while an earlier tail is still loud, that tail passes with the new hit.
- Hits buried in a similar tail (for example 16th-note open hi-hats with small accents) may not be recognised at the default Sensitivity and are then reduced together with the tail before them. Raise the Sensitivity for such material.
- What counts as a bed. A steady level is kept only when it sits at least 12 dB below the hits around it. A sustain or slow decay that settles 12 dB or more below its own attack can be treated as a bed and is then only shortened down to that level.
- Steady noise on its own is faded out once the detector reacts to one of its peaks. At very high Sensitivity, noise can trigger detections so often that it is faded out in the same way.
- After a bed stops, TailFit can keep its level as a floor for up to 4 seconds, so a hit right after it may not be shortened below that level until then.
- A detuned bass whose playback starts in the middle of a held note can be taken for a slow swell and left untouched until its next attack.
- The first hit after playback starts can cut through a bed until the next hit.
Factory presets
Default, Tight Kick, Short Snare, Tight Hats, Controlled Percussion, Clean Break, Tight Breakbeat, Short Bass, Controlled Pluck and Natural Tail.
Presets change the processing controls and the HP and LP filters (all factory presets have both filters off). They never change Output, Hear removed, Bypass or the accent colour. User presets saved with TailFit 1.0 load with both filters off.